ME8493 THERMAL ENGINEERING-I
Important questions
share it a link alone
Don't share as screenshot kind request
Unit-1
2.reheat and regenerative cycle
Unit-2
1.Volumetric, isothermal, isentropic efficiency problem
2.multistage air compressor
Unit-3
1.valve and port timing diagram , p-v digram
2.Air fuel ratio calculation
3.Combustion in SI and CI engine
Unit-4
1.Morse and heat balance test
2.multifuel injection system
3.magneto, battery and electronic lubrication and cooling
Unit-5
1.open and closed cycle problems
2.regenerative and intercooled
**Very important questions are bolded and may be asked based on this topic
- Check problem on that topic in ur notes and if not ask your staff problem on that topic
- If problem come on that topic try to attend and do write
- given data
- To find
- Formula used
- Solution
- If can final ans
don't waste my hardwork and valuable time
Contact uS
*These questions are expected for the exams This may or may not be asked for exams All the best.... from admin Santhosh
Thanks for your love and support guys keep supporting and share let the Engineers know about Us and leave a comment below for better improvements If there is any doubt feel free to ask me I will clear if I can or-else I will say some solutions ..get me through WhatsApp for instant updates ~$tuff$£ctorSYllabuSUNIT I GAS AND STEAM POWER CYCLES
Air Standard Cycles - Otto, Diesel, Dual, Brayton - Cycle Analysis, Performance and Comparison - Rankine, reheat and regenerative cycle
UNIT II RECIPROCATING AIR COMPRESSOR
Classification and comparison, working principle, work of compression - with and without clearance, Volumetric efficiency. Isothermal efficiency and Isentropic efficiency. Multistage air compressor with Intercooling. Working principle and comparison of Rotary compressors with reciprocating air compressors.
UNIT III INTERNAL COMBUSTION ENGINES AND COMBUSTION
IC engine - Classification, working, components and their functions. Ideal and actual: Valve and port timing diagrams, p-v diagrams- two stroke & four stroke, and SI & CI engines - comparison. Geometric, operating, and performance comparison of SI and CI engines. Desirable properties and qualities of fuels. Air-fuel ratio calculation - lean and rich mixtures. Combustion in SI & CI Engines - Knocking - phenomena and control.
UNIT IV INTERNAL COMBUSTION ENGINE PERFORMANCE AND SYSTEMS
Performance parameters and calculations. Morse and Heat Balance tests. Multipoint Fuel Injection system and Common Rail Direct injection systems. Ignition systems - Magneto, Battery and Electronic. Lubrication and Cooling systems. Concepts of Supercharging and Turbocharging-Emission Norms
UNIT V GAS TURBINES
Gas turbine cycle analysis - open and closed cycle. Performance and its improvement - Regenerative, Intercooled, Reheated cycles and their combinations. Materials for
Turbines.
UNIT I GAS AND STEAM POWER CYCLES
Air Standard Cycles - Otto, Diesel, Dual, Brayton - Cycle Analysis, Performance and Comparison - Rankine, reheat and regenerative cycle
UNIT II RECIPROCATING AIR COMPRESSOR
Classification and comparison, working principle, work of compression - with and without clearance, Volumetric efficiency. Isothermal efficiency and Isentropic efficiency. Multistage air compressor with Intercooling. Working principle and comparison of Rotary compressors with reciprocating air compressors.
UNIT III INTERNAL COMBUSTION ENGINES AND COMBUSTION
IC engine - Classification, working, components and their functions. Ideal and actual: Valve and port timing diagrams, p-v diagrams- two stroke & four stroke, and SI & CI engines - comparison. Geometric, operating, and performance comparison of SI and CI engines. Desirable properties and qualities of fuels. Air-fuel ratio calculation - lean and rich mixtures. Combustion in SI & CI Engines - Knocking - phenomena and control.
UNIT IV INTERNAL COMBUSTION ENGINE PERFORMANCE AND SYSTEMS
Performance parameters and calculations. Morse and Heat Balance tests. Multipoint Fuel Injection system and Common Rail Direct injection systems. Ignition systems - Magneto, Battery and Electronic. Lubrication and Cooling systems. Concepts of Supercharging and Turbocharging-Emission Norms
UNIT V GAS TURBINES
Gas turbine cycle analysis - open and closed cycle. Performance and its improvement - Regenerative, Intercooled, Reheated cycles and their combinations. Materials for
Turbines.